Workshop Equipment Advice & Insights

Installing a car hoist is a critical step for any automotive workshop or bodyshop aiming to improve efficiency and safety. A well-installed hoist allows easy access to the underside of vehicles, making repairs and maintenance faster and more effective. This guide covers the essential steps and considerations for installing a car hoist in Sydney, ensuring compliance with local standards and practical requirements. Preparing for Car Hoist Installation Before starting the instal

As a car owner, you know how crucial your vehicle’s paintwork is. It’s not just about aesthetics—paint enhances your car’s appearance, boosts its resale value, and provides a protective layer against environmental damage. If you’ve ever had your car repaired or repainted, you’ll also understand the importance of proper paint drying and curing. While we won’t dive into the technical details, curing is the stage where the paint fully hardens, reaching its maximum durability. Sk

Shortwave Infrared Lamps vs. Paint Booths: Roles and Differences in Body Shops Both shortwave infrared lamps and paint booths are used in body shops for paint drying and curing, but they differ significantly in working principles, applications, and efficiency. Below is a detailed comparison: I. Shortwave Infrared Lamps Functions: Localized Heating: Primarily used for drying and curing paint on small or localized areas. Rapid Drying: Shortwave infrared penetrates the paint sur

A two-post hoist installation should be planned around the exact equipment, its installation documents and the proposed site. This is a preparation checklist for workshop owners, not instructions for drilling anchors, connecting power or commissioning a hoist. Download the installation checklist The YOKI Australian Two-Post Hoist Installation Checklist is a 10-page printable record for competent installers, commissioners and project leads. It covers pre-installation documenta

1. Suspended Wheel Alignment System Technology: Uses mechanical gauges, sensors, and physical measurements (e.g., turnplates, measuring tapes). Requires the vehicle to be lifted on a hoist (suspended in the air) for undercarriage access. Use Cases: Ideal for heavy-duty vehicles (trucks, buses, lifted cars) or older models. Focuses on basic alignment angles (camber, caster, toe). Pros: Affordable and straightforward for simple adjustments. Durable in rugged workshop environmen

Compare 3D and 5D wheel alignment systems, including measurement scope, setup, workshop applications and when each system is suitable for professional alignment work.

A two-post hoist needs a model-specific inspection and maintenance programme. This guide explains the difference between an operator's pre-use checks and work that belongs to a competent service technician. It is not a substitute for the hoist manual, vehicle lifting information, workplace procedures or required inspections. Download the safety and maintenance manual The YOKI Vehicle Hoist Safety and Maintenance Manual is a 9-page printable safety pack for workshop managers,

Preparation, compatibility checks and safe working boundaries for swing-arm tyre changers, including when to stop and contact YOKI for support.

What is the difference between two-post Base-plate hoists and two- post overhead hoists? All of the two post above ground hoists have a power unit (240 volt single phase/415 volt three phase) located on one of the columns. The columns are symmetrical so the column with the mounting fixture for the power unit may be located on either side. ​ The power unit supplies pressurized hydraulic fluid to the cylinders (located in both columns) through hydraulic hoses that run between t

Concrete Thickness Most of our two post and scissor hoists require 15cm of concrete with 4.0 tone capacity. Please check our web site for the specifications of your hoist. Ceiling Height Check the ceiling height of your area to make sure it is adequate for installation of your new hoist. If you have exposed ceiling rafters...you may be able to position an overhead two post crossbeam in between the rafters (if they are "running" that way) OR you may be able to "run" the top cr

Know when to stop using a scissor hoist that is not lifting as expected, what details to record and when to request model-specific support from YOKI.

Keep a workshop wheel balancer reliable with practical operator checks, correct cleaning, equipment-life factors and clear service boundaries.

Practical first checks for common wheel balancer faults, plus clear guidance on what operators can inspect and when a technician is required.

A practical workshop guide to preparing, mounting and balancing a wheel correctly, with clear operator checks and service boundaries.